Programming Info
- New / Used ECM Programming (VIN and immobilizer) ... $100
- Airbag Modules Reset
- OPDS Module Initialization (in passenger seat) ... $40
- Fixes Airbag codes 81-xx & 85-xx
- Programming and Coding of all ECU's (non-security-related) .............. $100 - $150
- ECU swapping (if hardware matches)
- Programming of security related ECU's ................................................ $200 - $500
- DME/DDE swap (Digital Motor Electronics aka Engine Control Module). Used or new.
- List of supported DME's in E series:
- D62M57A0, D62M57B0, D60PSA0, D50M57A0, D50M57E1, D60M47A0, D60M57A0, MEV9N46L, ME9N45, ME9N62, ME9E65_6, N73_L0, N73_R0, ME9N62_2, MSV70, MS450DS0, N62_TUE, N62_TUE2.
- MSV80, MSD80, MSD81, MSD85, MSD85Y, MSS60, MEVD176K, ME17N45, MED17_2, MED17_2N, MEV17_2, MEV17N46, MEVD174K, MEVD174KW, MV1722, MVD1722, MEVD172, MEVD1724, MEVD1725, MEVD172Y, MEVD17KW, D70N47A0, D70N47B0, D71N47A0, D71N47B0, D71N47C0, D71N47D0, D72N47A0, D72N47B0, D73N47A0, D73N57A0, D73N57B0, D73N57C0, D73N57D0
- List of supported DME's in F series:
- MEVD172Y, MEVD172, MEVD1724, MEVD1725, N63TU_L0, N63TU_R0, S63TU_L0, S63TU_R0, MSD85, MSD87, MSV90
- List of supported DME's in E series:
- Immobilizer Box. Swap and "marriage" of Immobilizer Box with DME.
- E series: CAS1, CAS2, CAS3 and CAS3+
- F series: BDC /FEM
- Mileage Reset for BDC and FEM
- Change BDC and FEM ISN
- Change BDC and FEM VIN,
- DME/DDE swap (Digital Motor Electronics aka Engine Control Module). Used or new.
- EGS Transmission control module programming (used and new)....................................... $150 - $250
- BMW E series EGS ISN matching with CAS
- BMW F series EGS 8HP EWS Resetting
- Other programming services
- Occupancy Mat disable (through coding)... $100
- Notes: Passenger occupancy system
- Occupancy Mat disable (through coding)... $100
- ECM Software Update ... $100
- New/ Used ECM programming (VIN and Immobilizer) ... $150
- Passenger Seat Weight Sensor Calibration ... $50
- New/ Used ECM programming (VIN and Immobilizer) ... $150
- New/ Used ABS Module programming ... $100
- New/ Used SRS Module programming ... $100
- Engine Control Module Programming/Software Update (VIN and immobilizer) ... $150
- New/ Used SRS Module programming ... $100 - $150
- New/ Used Airbag Module Programming / ACU Variant Code Coding ... $100
- Fixes B1762 ACU Coding Error. This code appears when you install a new airbag module that hasn't been programmed to the car yet
- Occupancy Mat disable (through coding)... $50
- Notes: Passenger occupancy system
- Key programming, Regular key (up to 2018) ... $100
- Key programming, Smart key (up to 2018) ... $250
- Note: Keys programming is done through OBDII connector. No need to remove parts. All keys lost solution.
- New/ Used ECM Module programming ... $100
Tips
- Transmission
- "AT Oil Temp" is flashing after battery disconnect (2010-2011 Outback/Legacy, CVT Trans). ECM and TCM have no codes. Most likely cause is that CVT adaptation values has been lost and need to be relearned.
- "AT Oil Temp" is flashing after battery disconnect (2010-2011 Outback/Legacy, CVT Trans). ECM and TCM have no codes. Most likely cause is that CVT adaptation values has been lost and need to be relearned.
- Eyesight
- Lane Departure light ON? If no codes, press Lane Departure switch for 3 seconds.
- B28BA Steering angle and stereo camera correlation misaligned. Needs Active Lane Keep System calibration.
- BlindSpot
- No codes, but stops working after a short drive? If vehicle was hit in the back, most likely cause of that light is Blind Spot Module misalignment. Dealer only.
- New/ Used Engine Control Module Programming (VIN and immobilizer) ... $100
- Key Programming. Regular key & Smart key (up to 2017) ... $100
- Occupant Classification Calibration ... $40
- Fixes B1650, Occupant Classification System Malfunction